NEO mapper

Here's a proposal for a mapper format operating with a 16-bit segment register and allowing ROMs larger than the 2/4 MB limit of classic mappers.

Principles

This mapper format is designed to facilitate the creation of MSX games, not only by increasing the size of the ROM available for content, but also by offering programmers new possibilities for organizing their code and data.

Like conventional mappers, the basic idea is to use data write signals to the cartridge to change the value of the ROM segment visible in each of the mapper's banks (sub-pages). So, predefined addresses can be used to write to the mapper registers (see tables below). Read accesses, however, work as normal accesses to the memory visible through the banks.

Compared to conventional mappers, this proposal is based on two new main features:

• A 16-bit segment register,
• Banks covering all 4 pages of MSX memory space.

Page 3's usefulness is rather limited by its strong usage constraints, but page 0's makes it easy to have an extra 16 KB accessible at any time (either by temporarily disabling interrupts for the duration of accesses, or by adding its own ISR).

For the time being, we propose to reserve the 4 most significant bits for future extensions for the format (such as SRAM or sound chips support for example). This leaves 12 bits to select which segment is visible in each bank, for a maximum of 4096 segments. The reserved bits, must be set to 0.

Higher byte									Lower byte
15	14	13	12	11	10	9	8		7	6	5	4	3	2	1	0
0	0	0	0	Segment MSB					Segment LSB

The maximum ROM size is therefore 32 MB (for 8 KB segments) or 64 MB (for 16 KB segments).

Format

Write access to the mapper is use to change the value of the segment switching register of each bank. Here is the list of the predefined segment switching addresses.

As this new mapper uses 16-bit segment switching registers, it uses 2 bytes for the segment number to be selected in each bank. All even-numbered addresses (bit #0 of the address set to 0) access the low byte of the 16-bit register, while odd-numbered addresses (bit #0 of the address set to 1) access the high byte. This way, the segment number can be initialized at once with the Z80 instructions for 16-bit memory write access.

NEO-8 mapper

• Size of a segment: 8 KB
• Segment switching addresses:

Bank (8kB)	Switching address	Initial segment
0: 0000h~1FFFh	5000h (mirror at 1000h and 9000h)	0000h
1: 2000h~3FFFh	5800h (mirror at 1800h and 9800h)	0000h
2: 4000h~5FFFh	6000h (mirror at 2000h and A000h)	0000h
3: 6000h~7FFFh	6800h (mirror at 2800h and A800h)	0000h
4: 8000h~9FFFh	7000h (mirror at 3000h and B000h)	0000h
5: A000h~BFFFh	7800h (mirror at 3800h and B800h)	0000h

• Maximum number of segments: 4096
• Maximum ROM size: 32 MB

NEO-16 mapper

• Size of a segment: 16 KB
• Segment switching addresses:

Bank (16kB)	Switching address	Initial segment
0: 0000h~3FFFh	5000h (mirror at 1000h and 9000h)	0000h
1: 4000h~7FFFh	6000h (mirror at 2000h and A000h)	0000h
2: 8000h~BFFFh	7000h (mirror at 3000h and B000h)	0000h

• Maximum number of segments: 4096
• Maximum ROM size: 64 MB

Detection

For emulators and flash tool to detect the NEO mappers, the ROM have to include the following character right after the 16 bytes ROM header "NEOMAPPER".

It is recommended that

Appendix

Segment switching address format

The segment switching address is designed as:

16-bit address
15	14	13	12	11	10	9	8		7	6	5	4	3	2	1	0
P	P	x	x	x	B	B	B		x	x	x	x	x	x	x	R

Where:

• 'PP' (0-3) is the page selection for the MSX to redirect access to the mappers slot.
• 'BBB' (0-7) is the bank's register to write in.
• 'R' (0-1) is the segment switching register's byte selector (0: less significant byte; 1: most significant byte).
• 'x' can be any value (generating mirroring).

Bank switching cost

The cost of switching only the lower or higher byte of the 16-bit segment register is the same that switching segment for standard ASCII/Konami mappers.

; Direct access
LD A,n      ;  8 t-states
LD (nn),A   ; 14 t-states

; Indirect access
LD HL,nn    ; 11 t-states
LD (HL),n   ; 11 t-states

Although a program can avoid having to change the 2 bytes of the segment register at once, there are cases where this may be necessary. In such cases, the cost is higher, but remains reasonable.

; Direct access
LD HL,nn    ; 11 t-states
LD (nn),HL  ; 17 t-states

; Indirect access
LD DE,nn    ; 11 t-states
LD HL,nn    ; 11 t-states
LD (HL),E   ;  8 t-states
INC HL      ;  7 t-states
LD (HL),D   ;  8 t-states

MSXgl

MSXgl uses macros to wrap bank switching mechanisms. It would therefore be totally transparent for a user to switch, for example, from an ASCII8 or even Konami-SCC mapper, to an NEO-8 mapper.

#define SET_BANK_SEGMENT(bank, segment) /* ... */

// Make segment #30 visible through bank #1
SET_BANK_SEGMENT(1, 30);