Difference between revisions of "Debug device"
From MSX Game Library
| Line 39: | Line 39: | ||
‖ ‖ ‖ ‖ └───┴───┴───┴── Mode | ‖ ‖ ‖ ‖ └───┴───┴───┴── Mode | ||
0 ? 1 1 | 0 ? 1 1 | ||
| + | |||
| + | Note: The data address must be sent via the data register. The address must point to the address of the formatting string, followed by the various parameters. 8-bit values are stored on 16-bits. | ||
----------------------------------------------------------------------------- | ----------------------------------------------------------------------------- | ||
| Line 44: | Line 46: | ||
----------------------------------------------------------------------------- | ----------------------------------------------------------------------------- | ||
7 6 5 4 3 2 1 0 | 7 6 5 4 3 2 1 0 | ||
| − | ‖ └───┴───┴───┴───┴───┴───┴── [Command ID (0x7F = break point)] | + | ‖ └───┴───┴───┴───┴───┴───┴── [Command ID (0x7F = break point, 0x00 = reboot)] |
1 | 1 | ||
| Line 51: | Line 53: | ||
============================================================================= | ============================================================================= | ||
| − | + | Note: 16-bit values are sent in little-endian order (low byte first). | |
</syntaxhighlight> | </syntaxhighlight> | ||
[[category:Proposal]] | [[category:Proposal]] | ||
Revision as of 12:01, 9 May 2024
Proposal to improve the debugging protocol used by openMSX pseudo-device.
Based on: https://openmsx.org/manual/user.html#debugdevice
Debug device protocol
The additions are surrounded with [] prefix. This proposal is 100% compatible with the old one if unused bits was set to 0.
=============================================================================
Port 0x2E - Mode Set Register
=============================================================================
7 6 5 4 3 2 1 0
│ │ │ │ └───┴───┴───┴── Mode-specific parameters
│ │ └───┴────────────────── Output mode (0 = OFF, 1 = single byte, 2 = multi byte, [3 = formatted string])
│ └────────────────────────── Line feed mode (0 = line feed at mode change, 1 = no line feed)
└────────────────────────────── [Functionality (0 = output, 1 = command)]
-----------------------------------------------------------------------------
Functionality = output, Output mode = single byte
-----------------------------------------------------------------------------
7 6 5 4 3 2 1 0
‖ ‖ ‖ ‖ │ │ │ └── Hexadecimal mode (0 = OFF, 1 = ON)
0 ? 0 1 │ │ └────── Binary mode (0 = OFF, 1 = ON)
│ └────────── Decimal mode (0 = OFF, 1 = ON)
└────────────── ASCII mode (0 = OFF, 1 = ON)
-----------------------------------------------------------------------------
Functionality = output, Output mode = multi byte
-----------------------------------------------------------------------------
7 6 5 4 3 2 1 0
‖ ‖ ‖ ‖ │ │ └───┴── Mode (0 = hex, 1 = binary, 2 = decimal, 3 = ASCII mode)
0 ? 1 0 │ └────────── [Data width (0 = 8 bits; 1 = 16 bits)]
└────────────── [Signed (0 = unsigned, 1 = signed)]
-----------------------------------------------------------------------------
Functionality = output, Output mode = formatted string
-----------------------------------------------------------------------------
7 6 5 4 3 2 1 0
‖ ‖ ‖ ‖ └───┴───┴───┴── Mode
0 ? 1 1
Note: The data address must be sent via the data register. The address must point to the address of the formatting string, followed by the various parameters. 8-bit values are stored on 16-bits.
-----------------------------------------------------------------------------
Functionality = command
-----------------------------------------------------------------------------
7 6 5 4 3 2 1 0
‖ └───┴───┴───┴───┴───┴───┴── [Command ID (0x7F = break point, 0x00 = reboot)]
1
=============================================================================
Port 0x2F - Data Register
=============================================================================
Note: 16-bit values are sent in little-endian order (low byte first).